China Manufacture Steel F H Plastic Ring Liquid PE Filter Bag/Filter Sock With FDA Food Grade For Pharmaceutical

Basic commercial terms of liquid PE filter bag/filter sock

Product introduction of liquid PE filter bag/filter sock

Chinese manufactured steel & F H plastic ring liquid PE filter bag/socks with FDA food grade for pharmaceutical industry.

PE filter bag is made of polyester fiber filter cloth. It is a deep three-dimensional filter material made of 100% pure fiber by needling to form a three-dimensional.

Highly fluffy three-dimensional depth and tortuous filter layer. It is characterized by loose fiber structure which increases the carrying capacity of impurities.

This product belongs to the compound interception mode. It effectively removes solid and soft particles as larger particle impurities are trapped on the fiber surface while fine particles are captured in the deep layer of filter material.

Ensuring that they will not be damaged due to pressure increase during use and will have high filtration efficiency. In addition, the outer surface of the product receives high-temperature surface heat treatment through the application of instant singeing technology & calendaring treatment. It can effectively prevent the loss of fibers due to high-speed impact of liquid during filtration. Which ensures that there is no fiber separation causing filtrate pollution and avoids excessive clogging of filter holes caused by traditional rolling treatment and shortens the life of filter bags.

At the same time, the pressure difference is small and does not affect the flow rate.

Reasons for choosing liquid PE filter bag/filter sock

1. Liquid PE filter bag/sock has good performance at normal temperature and PE is the main filter material in bag filter with low cost.

2. Polyester has excellent electrical insulation, good wear resistance, high strength and good thermal stability. The operating temperature is 130 ℃ - 150 ℃.

3. The surface is smooth, the abrasion resistance is good, and the strength is high. After twisting, the strength is higher and the abrasion resistance is better. Therefore, the fabric has good air permeability, fast water flow rate and convenient cleaning.

Competitive Advantage of liquid PE filter bag/sock:

1. Micron rating is from 1 to 200

2. Temperature rating is up to 275° F

3. Wide chemical compatibility range

4. Depth loading material

5. High dirt holding capacity

6. Available in industry standard & custom sizes

7. Singed to reduce fiber migration

8. Felt materials meet FDA regulations for food contact under CFR21

Why Choose Sffiltech for Chinese manufactured steel & F H plastic ring liquid PE filter bag/filter sock with FDA food grade for pharmaceutical:

>As one of the leading developers of high quality, reliable filtration products for bag houses. When developing solutions we have always listened to our customers and considered the industry needs, which truly addresses the filtration system requirements of the modern industries.

>product reliability

>technical support for the lifetime of the filter bags

>Big stock for order supply stable

>Mass production supply with so many years’ experience

>Inspection for each order by our test person

>These Above attributes enable Sffiltech’s filtration solutions to deliver the most economic and quality products for our agent to resell in a filtration system.

Reliability:

Our reputation for reliability is based on many years of experience in the field, especially for china big filter bag market application and mass production. For example, steel plant, for top 10 enterprise. China has 6 from the 10 enterprise. So we have wide application experience for our filter bag in the bag house system.

Here is the summery of the reason why we have high reliability:

> conduct quality test of products and equipment for each order

> Mass production supply and get skilled from such experiences

>High quality needle punch production line

>Auto filter tube production line

>Skilled workers with more than 20 years’ experience

>We have huge supply in Chinese and the international market to support our filter bag business

>System approach

Once you become our partner for agent or end-user. We will get trusted, time-honored manufacturer and a system approach to your special requirement.

We will offer you the following;

.Design and manufacture the filter bags that fit your specific application

. We will process, analyze and optimize your total system performance

.We will provide technical support and troubleshooting for the lifetime of the filter bags

> Selected material ensures compliance with all food applications. In the case of sewn bags, a special lubricant-free thread material is used.

>An independent lab analysis ensures that FDA requirements are met

>Migration is strongly reduced through the careful selection of polymers that are considered to be safe under food law

>FDA seal ring prevents liquid bypass for safe filtration

>Special Single packaging keeps filter bags free from contamination during shipping and storage prior to use.

Sffiltech strongly recommends the use of an insertion tool that facilitates the insertion of the filter bag into the bag filter housing and ensures the correct alignment of the filter bag inside the restrainer basket.

>It is made in very clean workshop

>Special for certain FDA requirement environment

How to check what kinds of filter bag is needed by your bag house

You just change the filter bag from one economic supplier;

1. If you have the filter bag already in hand, then just take some picture for us first. Then we can get more than 80% of knowledge if we can make or not.

2. If you can send us the samples, then we can analyses the sample bag material and treatment.

3. We can make one sample for you to try your bag house within a few days.

You have a new bag house to build, you need one new filter bag suggestions:

1. We will send you one configuration file for you to fill. All about your bag house condition like temperature, chemical content and others. After you send it back to us, we will suggest you one kind filter bag to try.

2. Our engineer can arrange one online with your engineer or plan configuration for you.

How to be our agent?

1. Check our company detail and if you prefer to be our partner in future.

2. Check your market in your country if any chance to work in the filter field.

3. Then Email to us if you interest to join us.

FAQ about Chinese manufactured steel F H plastic ring liquid PE filter bag/filter sock with FDA food grade for pharmaceutical:

1. Q: Are you a trading company or a manufacturer?

A: We are the professional manufacturer of all kinds of filter bag, filter cloth & filter housing. We provide the full filtration solutions with our 16 years’ experience in the industry.

2. Q: May I have samples?

A: Yes, of course. Sample cost can be refunded if you place formal orders in the future.

3. Q: Can you make customized products?

A: Yes, of course. If you can provide us detailed specifications or drawings. Our mission is to make our customer’s idea of products into reality and provide the customer’s with satisfied solutions.

4. Q: Can I use our own designed package?

A: Yes, size, color, logo and packaging style all can be customized.

5. Q: What’s your MOQ?

A: Normally, 100 PCS/item. Any trial order which is less than MOQ is warmly welcomed. If you have a trial order, please feel free to contact us so that we can make some shipping recommendation for you to save the cost based on the quantity you need.

6. Q: I am a small business owner, Can I buy from you?

A: Yes, you are warmly welcomed. To grow with our customer is our goal. We would like to grow with you together.

7. Q: What is your general lead time?

A: Normally 3-7 working days for off-the-shelf samples and 10-30 days for bulk production.

8. Q: How should I pay you?

A: We strongly recommend Trade Assurance on online plat-forms. Service by T/T, L/C, Western Union, Money Gram etc are acceptable.

9. Q: What certificate do you have?

A: Our factory is ISO certified. We have CE, FDA and other certificate for the products we are manufacturing.

10: Q: How should I place an order?

A: Please kindly click” contact” and send email. Then our sales representative will recommend you suitable products for your selection also give some valuable suggestion for your selection.

Product Processing

liquid PE filter bag/filter sock size

liquid PE filter bag/filter sock structure

liquid PE filter bag/filter sock chemical performance

It is widely used in the following industries;

>Automotive coatings

>Paint

>Water purification

>Water treatment

>Pharmaceutical

>Catering Fine chemicals

>Petrochemical industry

>It is mainly used in the filtration of vegetable oil, edible oil, diesel oil, hydraulic oil, lubricating oil, animal oil, ink and other oily liquids.